![sound tools wallcat sound tools wallcat](https://i.ytimg.com/vi/pQp7dJ__LN0/maxresdefault.jpg)
At any time after that, if it fails, contact us and we will send you a replacement. If you are not happy with it within the first year, you can return it for a refund.
![sound tools wallcat sound tools wallcat](http://www.soundtools.com/images/news/Shieldedvsnonhome.jpg)
![sound tools wallcat sound tools wallcat](https://www.showtechnix.co.nz/wp-content/uploads/2020/07/Wallcat8-1.jpg)
4 Neutrik XLR connectors in front and 2 Amphenol RJ45 connections in back (allows or daisy-chaining). 4 CHANNEL XLR – Send audio and data from one room to another using installed shielded CAT5/6/7 cable.Would heatshrink over the Cat twisted pairs be good enough for a sub snake that will likely remain patched into the main snake? It should only come out to plug a band's splitter in or re-arrange the input order, so likely not very often. What is the best way to make a fan out from Cat5/6 cable?īut our budget is nearly non-existant, which is the reason I'm using Cat cable instead of actual multipair snake cable anyways, so $120 x 5 stage boxes is too much. So despite them sharing the ground connection, the other channels in the box will not get voltage when phantom is sent to just one. No! because +48 is sent over pins 2 and 3, pin 1 only provides the ground. Īre there any consequences to this approach? Looking at the PCB traces on this panel it appears so. Is this how RAT does it in their (expensive) superCAT cables, boxes, and tails? Share the drain wire to all the XLR connectors' pin 1? I'll be plugging in condensers and active DI's so I will need this. Central Ohio (614) 741-5306 oup 9-6pm EST TPG Corporate All Speakers AVL. Share on Facebook Tweet on Twitter Pin on Pinterest. Installation is easy once the Cat-5 line is in and RJ-45 terminated, the line merely plugs into one of the two jacks (input and parallel, if needed) on the rear of the plate. Choose from either input or output across 4 XLR channels that utilizes Cat5e, Cat6, or Cat7 cable to transmit superior analog audio, AES3, DMX and intercom signals to multiple locations. Designed for installations, the SoundTools WallCAT (50) puts four XLR’s (male or female) onto a wall plate that fits a USA standard 4×4 electrical junction box. It enables sending and receiving of audio and COM signals through CAT. SoundTools WC111 Two Gang Wall Panel with 4 Male XLR to RJ45 The WC111 WallCat is a 2-gang wall plate with 4 XLR male connectors and 2 RJ45 connectors. The Penn Group Electronics shipping audio, video, lighting, and more nationwide. The SoundTools WallCAT 8 is an easy-to-install 2 gang wall plate. SoundTools WallCAT Male XLR Silver Two Gang Wall Panel with 4 Male XLR to RJ45. Well yeah, it will work, but what about phantom power? Without pin 1, no +48. SoundTools WC121-S WallCAT - Wall Mounted Audio Transport - Female Silver. Leave all the grounds disconnected and call it good? How can I get 4 channels of balanced and shielded audio over 9 wires? I will be sure that the cable we order is shielded and has the extra drain wire. Because we are wiring the whole building for low voltage, I will have bulk Cat6 or Cat6a cable available and would like to run the stage boxes with those, probably hard-wired to the XLRs in the stage box, and made to fan out on the other end to the main snake. Each box has either 4 XLRs or 3 XLRs and 1 NL4. I've got some pop-up stage boxes from Parts Express to install in a stage for a new venue.